View TDA1307_204540.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
TDA1307 High-performance bitstream digital filter
Preliminary specification Supersedes data of July 1993 File under Integrated Circuits, IC01 1996 Jan 08
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
FEATURES * Multiple format inputs: I2S, Sony 16, 18 and 20-bit * 8-sample interpolation error concealment * Digital mute, attenuation -12 dB * Digital audio output function (biphase-mark encoded) according to IEC 958 * Digital silence detection (output) * Digital de-emphasis (selectable, FS-programmable) * 8 x oversampling finite impulse response (FIR) filter * DC-cancelling filter (selectable) * Peak detection (continuous) and read-out to microprocessor * Fade function: sophisticated volume control * Selectable 3rd/4th order noise shaping * Selectable dither generation and automatic scaling * Dedicated TDA1547 1-bit output
TDA1307
* Differential mode bitstream: complementary data outputs available * Simple 3-line serial microprocessor command interface * Flexible system clock oscillator circuitry * Power-on reset * Standby function * SDIP42 package.
QUICK REFERENCE DATA Voltages are referenced to VSS (ground = 0 V); all VSS and all VDD connections should be connected externally to the same supply. SYMBOL VDDC1,2,3 VDDOSC VDDAR VDDAL IDDC1,2,3 IDDOSC IDDAR IDDAL fXTAL Tamb Ptot PARAMETER supply voltage (pins 21, 41 and 8) supply voltage (pin 24) supply voltage (pin 32) supply voltage (pin 29) supply current (pins 21, 41 and 8) supply current (pin 24) supply current (pin 32) supply current (pin 29) oscillator clock frequency operating ambient temperature total power consumption VDD = 5 V VDD = 5 V VDD = 5 V VDD = 5 V CONDITIONS MIN. 4.5 4.5 4.5 4.5 - - - - - -20 - TYP. 5.0 5.0 5.0 5.0 75 2 2 1 - 400 MAX. 5.5 5.5 5.5 5.5 - - - - +70 - V V V V mA mA mA mA MHz C mW UNIT
33.8688 -
ORDERING INFORMATION PACKAGE TYPE NUMBER NAME TDA1307 SDIP42 DESCRIPTION plastic shrink dual in-line package; 42 leads (600 mil) VERSION SOT270-1
1996 Jan 08
2
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
GENERAL DESCRIPTION The TDA1307 is an advanced oversampling digital filter employing bitstream conversion technology, which has been designed for use in premium performance digital audio applications. Audio data is input to the TDA1307 through its multiple-format interface. Any of the four formats (I2S, Sony 16, 18 or 20-bit) are acceptable. By using a highly accurate audio data processing structure, including 8 times oversampling digital filtering and up to 4th order noise shaping, a high quality bitstream is produced which, when used in the recommended combination with the TDA1547 bitstream DAC, provides the optimum in dynamic range and signal-to-noise performance. With the TDA1307, a high degree of versatility is achieved by a multitude of functional features and their easy accessibility; error concealment functions,
TDA1307
audio peak data information and an advanced patented digital fade function are accessible through a simple microprocessor command interface, which also provides access to various integrated system settings and functions. TDA1307 plus TDA1547 high-performance bitstream digital filter plus DAC combination: For many features: * Highly accessible structure * Intelligent audio data processing. For optimum performance: * 4th order noise shaping * Improvement dynamic range (113 dB) * Improvement signal-to-noise (115 dB).
handbook, full pagewidth
fsystem = 768fs
20-bit fs
1-bit, 192fs
L
TDA1307
TDA1547
R
8 x oversampling FIR filter, 20-bit 24 x upsampling 3rd or 4th order noise shaping, 1-bit end quantization
1-bit high-performance digital-to-analog converter
3rd order analog postfilter, fo = 55 kHz Butterworth response
MGB983
Fig.1 High performance bitstream reconstruction system.
1996 Jan 08
3
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
BLOCK DIAGRAM
TDA1307
handbook, full pagewidth
WS 1
1fs AUDIO DATA INPUTS SCK 2 SD 3 EFAB 4
TDA1307
MULTIPLE FORMAT INPUT INTERFACE 19 RESYNC
10 ERROR CONCEALMENT, INTERPOLATION, MUTING DIGITAL OUTPUT 13 5 6 12 11 36 37 DE-EMPHASIS FILTER 22 23 DIGITAL SILENCE DETECTION
DOBM DSTB SBCL SBDA
DSR DSL TEST1 TEST2
25
VSSOSC XTAL1
FIR HALFBAND FILTER STAGE 1: 1fs to 2fs 38 DA 39 CL RAB 42 MICRO- PROCESSOR INTERFACE DC-CANCELLING FILTER
CRYSTAL OSCILLATOR
XTAL2
CLOCK GENERATION AND DISTRIBUTION
15 CMIC 7 CDEC 14 CLC1 17 CLC2 18 CDCC
PEAK DETECTION
POR VDDC3 VDDC1 VDDOSC VDDAL VDDAR VDDC2
20 FADE FUNCTION VOLUME CONTROL
9 16
8
VSSC2 VSSC3 VSSAL VSSAR VSSC1
21
FIR HALFBAND FILTER STAGE 2: 2fs to 4fs
30 31 40
24 FIR HALFBAND FILTER STAGE 3: 4fs to 8fs
29
32 DITHER AND SCALING 41
3rd/4th ORDER NOISE SHAPER
27 DOL
28 NDOL
35 CDAC
34 NDOR
33 DOR
26
MGB989
MODE
BITSTREAM DATA OUTPUTS
Fig.2 Block diagram.
1996 Jan 08
4
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
PINNING SYMBOL WS SCK SD EFAB SBCL SBDA CDEC VDDC3 VSSC2 DOBM PIN 1 2 3 4 5 6 7 8 9 10 O TYPE, I/O I I I I(1) I I O clock input to data interface data input to interface DESCRIPTION word select input to data interface
TDA1307
error flag (active HIGH): input from decoder chip indicating unreliable data subcode clock: a 10-bit burst clock (typ. 2.8224 MHz) input which synchronizes the subcode data subcode data: a 10-bit burst of data, including flags and sync bits, serially input once per frame, clocked by burst clock input SBCL decoder clock output: frequency division programmable by means of pins 14 (CLC1) and 17 (CLC2) to output 192, 256, 384 or 768 times fs positive supply 3 ground 2 digital audio output: this output contains digital audio samples which have received interpolation, attenuation and muting plus subcode data; transmission is in biphase-mark code digital silence detected (active LOW) on left channel digital silence detected (active LOW) on right channel DOBM standby mode enforce pin (active HIGH) application mode programming pin for CDEC (pin 7) frequency division clock output, provided to be used as running clock by microprocessor (in master mode only), output 96fs ground 3 application mode programming pin for CDEC (pin 7) frequency division master / slave mode selection pin resynchronization: out-of-lock indication from data input section (active HIGH) power-on reset (active LOW) supply voltage 1 crystal oscillator terminal: local crystal oscillator sense forced input in slave mode crystal oscillator output: drive output to crystal positive supply connection to crystal oscillator circuitry ground connection to crystal oscillator circuitry
DSL DSR DSTB CLC1 CMIC VSSC3 CLC2 CDCC RESYNC POR VDDC1 XTAL1 XTAL2 VDDOSC VSSOSC MODE DOL NDOL VDDAL VSSAL VSSAR VDDAR DOR
11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
O O I(2) I O
I I O I(2) I O
I(2) O O
evaluation mode programming pin (active LOW); in normal operation, this pin should be left open-circuit or connected to the positive supply data output left channel to bitstream DAC TDA1547 complementary data output left channel to TDA1547 in double differential mode positive supply connection to output data driving circuitry, left channel ground connection to output data driving circuitry, left channel ground connection to output data driving circuitry, right channel positive supply connection to output data driving circuitry, right channel
O
data output right channel to TDA1547
1996 Jan 08
5
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
SYMBOL NDOR CDAC TEST1 TEST2 DA CL VSSC1 VDDC2 RAB Notes
PIN 34 35 36 37 38 39 40 41 42
TYPE, I/O O O I(1) I(1) I/O(2) I(2)
DESCRIPTION complementary data output right channel to TDA1547 in double differential mode clock output to bitstream DAC TDA1547 test mode input; in normal operation this pin should be connected to ground test mode input; in normal operation this pin should be connected to ground bidirectional data line intended for control data from the microprocessor and peak data from the TDA1307 clock input, to be generated by the microprocessor ground 1 supply voltage 2
I(2)
command / peak data request line
1. These pins are configured as internal pull-down. 2. These pins are configured as internal pull-up.
handbook, halfpage
WS SCK SD EFAB SBCL SBDA CDEC VDDC3 VSSC2
1 2 3 4 5 6 7 8 9
42 RAB 41 VDDC2 40 VSSC1 39 CL 38 DA 37 TEST2 36 TEST1 35 CDAC 34 NDOR 33 DOR
DOBM 10 DSL 11 DSR 12 DSTB 13 CLC1 14 CMIC 15 VSSC3 16 CLC2 17 CDCC 18 RESYNC 19 POR VDDC1 20 21
MGB980
TDA1307
32 VDDAR 31 VSSAR 30 VSSAL 29 VDDAL 28 NDOL 27 DOL 26 MODE 25 VSSOSC 24 VDDOSC 23 XTAL2 22 XTAL1
Fig.3 Pin configuration.
1996 Jan 08
6
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
FUNCTIONAL DESCRIPTION In the block diagram, Fig.1, a general subdivision into three main functional sections is illustrated. The actual signal processing takes place in the central sequence of blocks, a representation of the audio data path from top to bottom. The two blocks named "Microprocessor Interface" and "Clock Generation and Distribution" fulfil a general auxiliary function to the audio data processing path. The Microprocessor Interface provides access to all the blocks in the audio path that require or allow for configuration or selection, and manipulates data read-out from the Peak Detection block, all via a simple three-line interface. The Clock Generation and Distribution section, driven either by its integrated oscillator circuit with external crystal or by an externally provided master clock, provides the data processing blocks with timebases, manages the system mode dependent frequency settings, and conveniently generates clocks for external use by the system decoder IC and microprocessor. Following are detailed explanations of the functions of each block in the audio data processing path and their setting options manipulated by the microprocessor interface, the use of the microprocessor interface, and the functions of the clock section with its various system settings. Clock generation and distribution The clock generation section of the TDA1307 is designed to accommodate two main modes. The master mode, in which the TDA1307 is the master in the digital audio system, and for which the clock is generated by connecting Table 1 Clock divider programming CLC1 0 0 1 1 CLC2 0 1 0 1 CDEC OUTPUT FREQUENCY 256fs 384fs 768fs 192fs
TDA1307
a crystal of 768fs (33.8688 MHz) to the crystal oscillator pins XTAL1 (pin 22) and XTAL2 (pin 23); and the slave mode, in which the TDA1307 is supplied a clock by the IC in the system that acts as the master (e.g. the digital audio interface receiver). In this event a clock signal frequency of 256fs is input to pin XTAL1. Master or slave mode is programmed by means of pin CDCC (pin 18) logic 1 for master and logic 0 for slave mode. The circuit diagram of Fig.4 shows the typical connection of the external oscillator circuitry and crystal resonator for master mode operation. Note that the positive supply VDDOSC is the reference to the oscillator circuitry. The LC network is used for suppression of the fundamental frequency component of the overtone crystal. Figure 5 shows how to connect for slave mode operation. A clock frequency of typical 256fs and levels of 0 V/+5 V is input to XTAL1 via AC coupling. The 100 k resistor and the 10 nF capacitor are required to provide the necessary biasing for XTAL2 by filtering and feeding back the output signal of XTAL1. Besides generating all necessary internal clocks for the audio data processing blocks and the clock to the DAC, the clock generation block further provides two clocks for external use when operating in master mode. Pin CDEC (pin 7) is used as the running clock for the system decoder IC, and pin CMIC (pin 15) is used as the running clock for the system microprocessor. CMIC outputs, by a fixed divider ratio to XTAL2, a clock signal at 96fs. For CDEC the divider ratio is programmable by means of pins CLC1 (pin 14) and CLC2 (pin 17). Table 1 gives the clock divider programming relationships.
1996 Jan 08
7
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, halfpage
XTAL2 3.3 H 10 k 1 nF 10 pF 10 pF 100 k 33.8688 MHz XTAL1
23
22
TDA1307
VDDOSC 24
+5 V VSSOSC 25
MGB981
Fig.4 External crystal oscillator circuit.
handbook, halfpage
20 pF fi = 256fs 30 pF 100 k
XTAL2
23
XTAL1 10 nF +5 V VDDOSC
22
TDA1307
24
VSSOSC
25
MGB982
Fig.5 External clock input connections.
1996 Jan 08
8
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
Microprocessor interface The microprocessor interface provides access to virtually all of the functional blocks in the audio data processing section. Its destination is two-fold: system constants (such as input format and sample frequency) as well as system variables (attenuation, muting, de-emphasis, volume control data etc.) can be `written to' the respective blocks (command mode), and continuously collected stereo peak data `read from' the peak detection block (peak request). The system settings are stored in the TDA1307 in an internal register file. Peak data is read from the stereo peak value register.
TDA1307
THREE-LINE MICROPROCESSOR INTERFACE BUS Communication is realized by a three-line bus, consisting of the following signals (see Fig.6): * Clock input CL (pin 39), to be generated by the microprocessor * Command/request input RAB (pin 42), by which either of the two mode commands (RAB = 0) and peak request (RAB = 1) are invoked * Bidirectional data line DA (pin 38), which either receives command data from the microprocessor or outputs peak data from the peak detection block. CL and RAB both default HIGH by internal pull-up, DATA is 3-state (high impedance, pull-up, pull-down).
handbook, full pagewidth
+
RAB 42
+
REQUEST/COMMAND COMMAND DATA
DA/ACK 38
+
CL 39
PEAK DATA
CLOCK TDA1307
MGB984
MICROPROCESSOR
Fig.6 Three-line microprocessor interface bus.
1996 Jan 08
9
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
INITIALIZATION OF THE BUS RECEIVER The microprocessor interface section is initialized automatically by the power-on reset function, POR (pin 20). A LOW input on POR will initiate the reset procedure, which encompasses a functional reset plus setting of the initial states of the control words in the command register file. A wait time of at least one audio sample time after a LOW-to-HIGH transition of POR must be observed before communication can successfully be established between the TDA1307 and the microprocessor. In addition to the POR function, a software reset function issued from the microprocessor is provided (see section "Organization and programming of the internal register file"), which has the sole function of reinstating the initial values of the microprocessor control register. More information on initializing the TDA1307 can be found under "Application Information". COMMAND PROTOCOL The protocol for writing data to the TDA1307 is illustrated in Fig.7. The command mode is invoked by forcing RAB LOW. A unit command is given in the form of an 8-bit burst on the DA line, clocked on the rising edge of CL. The command consists of 4 address bits followed by 4 control data bits (both MSB first). A next command may be immediately issued while keeping RAB forced LOW. Only commands for which the MSB of the address bits is
TDA1307
LOW are accepted; of the remaining set of addresses, only four have meaning (see section "Organization and programming of the internal register file"). The command input receiver is provided with a built-in protection against erroneous command transfer due to spikes, by a 2-bit debounce mechanism on lines DA and CL. The waveforms on these lines are sampled by the receiver at the internal system clock rate 256fs. A state transition on DA or CL is accepted only when the new state perseveres for two consecutive sampled waveform instants. ORGANIZATION AND PROGRAMMING OF THE INTERNAL
REGISTER FILE
Command data received from the microprocessor is stored in an internal register file (see Table 2), which is organized as a page of 10 registers, each containing a 4-bit command data word (D3 to D0). Access to the words in the register file involves two controls: selection of the address of a set of registers (by means of A3, A2, A1 and A0) and setting the number of the bank in which the desired register is located (by means of the `bank bits' B0 and B1). First the desired bank is selected by programming the command word at address 0000 (supplying the bank bits plus refreshing bits ATT and DIM). A subsequent addressing (one of three addresses, 1H, 4H and 6H) will yield access to the register corresponding to the last set bank.
handbook, full pagewidth
tDRW tCKL RAB tCKH
CL
1
8
DA (TDA1307) tDSM DA (P) A3 A2 A1 tDHM A0 D3 D2 D1 D0
DA t
A3
A2
A1
A0
D3
D2
D1
D0
MGB995
Fig.7 Microprocessor command protocol.
1996 Jan 08
10
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
Table 2 Microprocessor control register file ADDRESS BANK A3 0 0 A2 0 0 A1 0 0 A0 B0 0 1 X 0 1 1 0 1 0 0 0 1 1 0 1 1 0 0 1 1 B1 X 1 0 1 1 0 1 1 0 1 BANK B0 FCON FSS7 FSS3 DCEN FN7 FN3 DEMC1 INS1 RES2 BANK B1 DIT FSS6 FSS2 DCSH FN6 FN2 DEMC0 INS0 NS ATT FSS9 FSS5 FSS1 FN9 FN5 FN1 RES0 FS1 RST DIM FSS8 FSS4 FSS0 FN8 FN4 FN0 RES1 FS0 STBY D3 D2 D1 D0
TDA1307
INITIAL STATE
0011 0000 0010 1000 0111 0000 1101 0000 0000 1000
Following is a list of the programming values for the various control words in the register file. Information on the meaning of the different controls can be found under the sections covering the corresponding signal processing blocks (see sections "Multiple format input interface" to "Third and fourth order noise shaping").
DIT
Dither control bit: logic 1 to activate dither addition, logic 0 deactivates.
FSS9 to FSS0
Fade function 10-bit control value to program fade speed, in number of samples per fade step.
BANK B0, BANK B1
Programming of the bank bits is given in Table 2. The bank bits can be changed by addressing register location 0000. Subsequent addressing will result in access of locations according to the last selected bank.
DCEN
DC-filter enable bit: logic 1 enables subtraction of the DC-level from the input signal, logic 0 disables.
ATT
Attenuation control bit: logic 1 to activate -12 dB attenuation, logic 0 to deactivate. As the attenuate control bit shares a control word with the bank bits, ATT has to be refreshed each time a new bank is selected.
DCSH
DC-filter sample or hold control bit: when DCSH = 0 the DC-level of the input signal is continuously evaluated. When DCSH = 1 the once acquired DC value, to be subtracted from the input signal, is held constant.
DIM
Digital mute control bit: logic 1 to activate mute, logic 0 to deactivate. An active digital mute will override the attenuation function. As with ATT, DIM needs to be refreshed with each change in bank selection.
FN9 to FN0
Fade function 10-bit control value to program volume level.
DEMC1, DEMC0
De-emphasis function enable and fs selection bits.
FCON
Fade function control bit: logic 1 to activate the fade function, logic 0 to deactivate.
1996 Jan 08
11
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
Table 3 De-emphasis mode programming DEMC0 0 1 0 1 DE-EMPHASIS FUNCTION de-emphasis disabled de-emphasis for fs = 32.0 kHz de-emphasis for fs = 44.1 kHz de-emphasis for fs = 48.0 kHz
TDA1307
RST
Software reset function. When RST = 1 the contents of the microprocessor control registers will immediately be preset to their initial values as shown in Table 2. As part of this reset action, bit RST is automatically returned to its initial state 0, that being normal operation.
DEMC1 0 0 1 1 Table 4 INS1 0 0 1 1 Table 5 FS1 0 0 1 1
STBY
Standby mode control bit. When STBY = 1 the standby mode will be initiated (explained under the section treating the Digital Output block). STBY = 0 for normal activity. PEAK DATA OUTPUT PROTOCOL The peak data read-out protocol is illustrated in Fig.8. A peak request is performed by releasing RAB (which will be pulled HIGH by TDA1307) while CL = HIGH, and maintaining RAB = 1 throughout the peak data transmission. TDA1307 will acknowledge the peak request by returning a LOW state on the DA line. Upon this peak acknowledge, the microprocessor may commence collecting data from the internal peak data output register (16-bit Left, 16-bit Right channel peak data) by sending a clock onto the CL line. The contents of the peak data output register will not change during the peak request. The first peak bit, the MSB of the Left channel peak value, is output upon the first LOW-to-HIGH transition of CL. To access Right channel peak value, all 16 bits of channel Left have to be read out, after which up to 16 bits of Right channel peak data may be read out. The peak data read out procedure may be aborted at any instant by returning RAB LOW, marking the end of the peak request: the internal peak register will be reset and the peak detector will start collecting new peak data and transferring this to the peak data output register.
Input format programming INS0 0 1 0 1 I2S INPUT FORMAT up to 20 bits Sony format 16 bits Sony format 18 bits Sony format 20 bits
Sample frequency indication programming FS0 0 1 0 1 DOBM SAMPLE FREQUENCY INDICATION fs = 44.1 kHz fs = 48.0 kHz no meaning fs = 32.0 kHz
RES2 to RES0
These are reserved locations and have no functional meaning in the TDA1307.
INS1, INS0
Input format selection control bits.
FS1, FS0
Sample frequency indication control bits for the digital output section.
NS
Control bit for Noise Shaper section. When NS = 0, 3rd order noise shaping is selected; when NS = 1, 4th order noise shaping is selected.
1996 Jan 08
12
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, full pagewidth
tDWR RAB tDSP CL 1 tDHP
READ PEAK DATA
DA (TDA1307)
Q1
Q2
Q3
Q31
Q32
DA (P)
DA
Q1
Q2
Q3
Q31
Q32
MGB996
Fig.8 Peak data output protocol.
Multiple format input interface Data input to the TDA1307 is accepted in four possible formats, I2S (with word lengths of up to 20 bits), and Sony formats of word lengths 16, 18 and 20-bit. The general appearance of the allowed formats is given in Fig.9. The selection of a format is achieved through programming of the appropriate bits in the microprocessor register file. Characteristic timing for the input interface is given in the diagram of Fig.10. SYNCHRONIZATION For correct data input to reach the central controller of TDA1307, synchronization needs to be achieved to the incoming 1fs I2S or Sony format input signals. The incoming WS signal is sampled to detect whether its phase transitions occur at the correct synchronous timing instants. This sampling occurs at the TDA1307 internal clock rate, 256fs. After one phase transition of WS, the next is expected after a fixed delay, otherwise the condition is regarded as out-of-lock and a reset is performed, this operation is repeated until synchronization is achieved. To allow for slight disturbances causing unnecessary frequent resets, the critical WS transitions are expected within a tolerance window (-4 to +4 periods of the 256fs internal sampling clock instants).
The reset action is flagged on the RESYNC (pin 19) output, which may be optionally used for muting or related purposes. RESYNC becomes HIGH the instant a reset is initiated, and remains in that state for at least one sample period (1/fs). ERROR FLAG INPUT EFAB The error flag input EFAB (pin 4) is intended as request line from the system decoder to the digital filter to indicate erroneous audio samples requiring concealment. A detected HIGH on input EFAB will be relayed by the input interface block to the error concealment block, where the samples flagged as erroneous will be processed accordingly.
1996 Jan 08
13
andbook, full pagewidth
1996 Jan 08
SCK EFAB WS SD 1 SCK
Philips Semiconductors
High-performance bitstream digital filter
1
2
n
32
1
2
n
32
1
2
LEFT
RIGHT
MSB
B2
MSB
B2
MSB
B2
SAMPLE IN LEFT INPUT FORMAT I2S
SAMPLE IN RIGHT
SAMPLE IN LEFT
2
3
4
5
6
7
8
9
10
23
24
1
2
3
4
5
6
7
8
9
10
23
24
14
WS LEFT RIGHT SD MSB B2 B15 LSB MSB B2 B15 LSB SAMPLE IN LEFT INPUT FORMAT SONY 16-BIT SAMPLE IN RIGHT SD MSB B2 B3 B4 B17 LSB MSB B2 B3 B4 B17 LSB SAMPLE IN LEFT INPUT FORMAT SONY 18-BIT SAMPLE IN RIGHT SD MSB B2 B3 B4 B5 B6 B19 LSB MSB B2 B3 B4 B5 B6 B19 LSB
MGB999
Preliminary specification
SAMPLE IN LEFT
INPUT FORMAT SONY 20-BIT
SAMPLE IN RIGHT
TDA1307
Fig.9 Input formats.
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, full pagewidth
RIGHT WS LEFT tSU;WS tr tHB tf tLB tHD;WS
RIGHT
LEFT
SCK
tSU;DAT
tHD;DAT
SD
MGB998
Fig.10 Typical I2S-bus data waveforms.
Error concealment, interpolation and muting The error concealment functional block performs three functions: 1. interpolation of up to eight consecutive erroneous audio samples flagged as such by input EFAB 2. attenuation 3. muting of incoming audio, both the latter if so activated by means of the microprocessor registers. Furthermore, as these functions constitute error processing functions, operation of any of these functions is reported to the digital output DOBM by setting the validity flag. EIGHT-SAMPLE INTERPOLATION Incoming audio samples may be visualized as entering a memory pipeline, nine audio sample instants in depth, upon entering the error concealment block. Any audio samples marked as erroneous by the flag input EFAB will be reconstructed by linear approximation from the values of the adjacent correct samples (the last correct sample still available, and the next correct sample). The linear interpolation is started as soon as a correct sample becomes available within nine sampling instants. Should a flagged erroneous condition persevere for over eight sampling instants, then the last correct sample will be held for as long as necessary, i.e. until the next correct sample enters the pipeline. The linear approximation is then 1996 Jan 08 15
initiated over the maximum interpolation interval of eight sampling instants. ATTENUATION The concealment block incorporates a digital -12 dB attenuation function intended to be used in program search or other player actions that may generate audible transitional effects such as loud clicks. The attenuate function is activated by means of bit ATT in the microprocessor register file. Setting this bit to logic 1 causes the next audio sample (attenuate never takes action on incomplete samples) to be attenuated with immediate effect (the validity flag of the digital audio output DOBM is set). The interpolation facility is called upon when an attenuate command is given while the incoming data is flagged as invalid by EFAB. If no more than eight samples in succession are invalid, attenuate may take immediate effect (this causes the output value to ramp linearly to the final attenuated level). If nine or more samples in a row are flagged erroneous, attenuation is postponed and the last good sample held, until the next good sample becomes available. Upon that instant, the output ramps linearly, over the maximum interpolation time span, to the attenuated first correct sample. Releasing attenuate (bit ATT reset to 0) always has immediate effect (i.e. the next complete audio sample will pass unattenuated).
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
MUTING The digital mute of the error concealment block immediately (i.e. on the next whole audio sample) sets the input to the digital filter to all zeros, regardless of any other current action in the error concealment block. The digital mute function is activated by means of bit DIM in the microprocessor register file. Setting this bit to logic 1 causes the next audio sample to be muted (the validity flag of the digital audio output DOBM is set). Releasing the digital mute function (resetting bit DIM to 0) will cause the output of the error concealment block to approach the unaffected audio sample value by linear approximation, on the condition that the mute action spanned at least 8 consecutive audio samples. If there are samples in error at the time of releasing mute, the release action is postponed until good data becomes available, after which the linear ramp can be made over the maximum interpolation time span. Digital output (DOBM) The DOBM block constructs a biphase modulated digital audio output signal which complies to the IEC standard 958, to be used as a digital transmission link between digital audio systems. A variety of inputs are combined, arranged and modulated to finally form the output biphase-mark sequence. The inputs are the following: * left and right audio data, word length 20-bit, as delivered by the error concealment block
TDA1307
* the Validity flag as output by the error concealment block * subcode information, as acquired by input via pins SBDA (pin 6) and SBCL (pin 5) * sampling frequency information as set by means of bits FS1 and FS0 in the microprocessor register file. As the digital output function is not always required, and can give rise to interference problems in high-quality audio conversion systems, the DOBM output can be switched on or off by means of pin DSTB (digital output standby, 13). Leaving DSTB open-circuit will cause it to pull HIGH and deactivate the DOBM output; tying DSTB LOW enables the digital output function. The programming of bits FS1 and FS0 is specified in Table 5 under section "Microprocessor interface". The DOBM block of TDA1307 translates the settings of these bits to the appropriate corresponding information in the digital audio output sequence (as specified by IEC 958). The inputs SBDA (subcode data, 6) and SBCL (subcode clock, 5) allow for the merging of subcode data into the output DOBM signal. The input sequence via these inputs is defined as 10-bit burst words, arranged as illustrated in Fig.11; the bit nomenclature corresponds to that used in the IEC standard 958. Both subcode data and clock signals are normally supplied by the decoder of the digital audio system (e.g. SAA7310). For set-up and hold timing of the SBDA and SBCL inputs, restrictions identical to the audio data inputs are valid.
handbook, full pagewidth
Q-CHANNEL PARITY CHECK FLAG (0 = FAIL)
SUBCODING ERROR FLAG
SYNC (active LOW)
SBDA
P-BIT
W
V
U
T
S
R
Q
P-BIT
SBCL
MGB997
2.8224 MHz (typ.) BURST CLOCK
Fig.11 Format of subcode data input.
1996 Jan 08
16
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
Digital silence detection The TDA1307 is designed to detect digital silence conditions in channels left and right, separately, and report this via two separate output pins, one for each channel, DSL (pin 11) and DSR (pin 12). This function is implemented to allow for external manipulation of the audio signal upon absence of program material, such as muting or recorder control. The TDA1307 itself does not influence the audio signal as a result of digital silence; the sole function of this block is detection, and any further treatment must be accomplished externally. An active LOW output is produced at these pins if the corresponding channel carries either all zeroes for at least 8820 consecutive audio samples (200 ms for fs = 44.1 kHz). The digital silence detection block receives its left and right audio data from the error concealment block (implying that a digital mute action will produce detection of a digital silence condition), and passes it unaffected to the next signal processing stage, the de-emphasis block. De-emphasis filter The TDA1307 incorporates selectable digital de-emphasis filters, dimensioned to produce, with extreme accuracy, the de-emphasis frequency characteristics for each of the three possible sample rates 32, 44.1 and 48 kHz. As a 20-bit dynamic range is maintained throughout the filter, considerable margin is kept with respect to the normal CD resolution of 16-bit i.e. the digital de-emphasis of TDA1307 is a truly valid alternative to analog de-emphasis in high-performance digital audio systems. Selection of the de-emphasis filters is performed via the microprocessor interface, bits DEMC1 and DEMC0, for which the programming is given in Table 3. Oversampling digital filter The oversampling digital filter in the digital audio reconstruction system is of paramount influence to the fidelity of signal reproduction. Not only must the filter deliver a desired stop-band suppression while sustaining a certain tolerated pass-band ripple, but it must also be capable of faithfully reproducing signals of high energy content, such as signals of high level and frequency, square wave-type signals and impulse-like signals (all of these examples have their counterparts in actual music program material). Filters optimized only towards pass-band ripple and stop-band suppression are capable of entering states of overload because of the clustered energy content of these signals, thus introducing audible
TDA1307
degradations in processing the mentioned types of excitations. To dimension a high-fidelity digital filter, a balance must be established between filter steepness and overload susceptibility. The oversampling digital filter function in the TDA1307 is designed, in combination with the noise shaper, to deliver the highest fidelity in signal reproduction possible. Not only are stop-band suppression and pass-band ripple parameters to the design, but also the prevention of detrimental artifacts of too extreme filtering: impulse and high-level overload responses. The outcome is a patented design excelling in natural response to most conceivable audio stimuli. It is realized as a series of three half-band filters, each oversampling by a ratio of two, thus achieving an eight times oversampled and interpolated data output to be input to the noise shaper. Each stage has a finite impulse response with symmetrical coefficients, which makes for a linear phase response. Filter stages 1, 2 and 3 incorporate 119, 19 and 11 delay taps respectively. To maintain an output accuracy of 20 bits, an internal data path word length of 39 bits is used to supply the required headroom in multiplications. Requantization back to 20-bit word length is performed by noise shaping (thus effectively preventing rounding errors in so far as they have effect in the audio frequency band), at the output of each filter section. The successive half-band filter stages are, for efficiency, distributed over the audio data processing path: DC-filtering, peak value reading and volume control are performed between stages 1 and 2 (the 2fs domain). DC-cancelling filter A mechanism for optionally eliminating potential DC content of incoming audio data is implemented in the TDA1307 for three main reasons. Most importantly because it is called for by the implementation of volume control in the TDA1307. An audio signal that is to be subjected to volume control (multiplication by a controlled attenuation factor) should be free of offset, otherwise the controlled multiplication will produce the undesired side effect of modulating the average DC content. The second reason is supplied by the implementation of audio peak data read-out in the TDA1307. As the peak value is obtained from the absolute value of the audio data referenced to zero DC level, its accuracy is impaired by the presence of residual DC information, progressively so for lower audio levels. The third reason is brought about by application of the noise shaper. To optimize the dynamic behaviour of the noise shaper especially for low-level signals, it is supplied a predefined offset, sometimes referred to as DC dither. Taking no precautions against DC 17
1996 Jan 08
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
content of the source audio data may render the DC dither potentially ineffective. In applications where the DC content of the audio information may be expected, application of the selectable DC filter may be opted for. It is implemented as a first-order high-pass filter with a corner frequency of 2 Hz. Control of the DC filter is achieved by accessing the appropriate bits DCEN (DC filter enable) and DCSH (DC filter sample or hold) in the microprocessor register file. The principle of operation is illustrated in Fig.12. The output of the DC filter, referred to in the diagram as `audio output' always equals the audio input subtracted by the output of the low-pass branch. Depending on the control bit DCSH, this subtraction value is either the last value held constant or a value continuously adapting to incoming DC content. The DC filter is effectively switched on or off via control bit DCEN, which selects the input of the low-pass section either to be the audio input data (the output of the low-pass section will settle to the low frequency content of the audio data so that the filter is on) or a preset value of zero (low-pass output will settle to zero meaning `filter off'). The constant mode is implemented to provide a mode in which a stable subtraction value is guaranteed; in this mode however the high-pass function is inhibited so there is no adaptation to changes in the DC content of the incoming source information. Peak detection The TDA1307 provides a convenient way to monitor the peak value of the audio data, for left and right channels individually, by way of read-out via the microprocessor interface. Peak value monitoring has its applications
TDA1307
mainly in digital volume unit measurement and display, and in automatic recording level control. The peak level measurement of the TDA1307 occurs with a resolution of 16-bit, providing a dynamic range amply suitable for all practical applications. The output of the peak detection block is a register of two 16-bit words, one for each channel, representing the absolute value of the accumulated peak value, accessible via the microprocessor interface. The peak detection block continuously monitors the audio information arriving from the DC-cancelling filter, comparing its absolute value to the value currently stored in the peak register. Any new value greater than the currently held peak value will cause the register to assume the new, greater value. Upon a peak request (for which the protocol is described in section "Peak data output protocol"), the contents of the peak register are transferred to the microprocessor interface. After a read action, the peak register will be reset, and the collection of new peak data started. The peak detection block receives data that has been processed by the first half-band stage of the oversampling interpolating digital filter (in the 2fs domain, but the peak detection `samples' at 1fs for efficiency). This means that the scaling applied in this first half-band stage is noticeable in the measured peak value. The frequency-independent attenuation factor of the first half-band filter equals 0.175 dB - this results in a possible range for the output peak value of 0 to 32114. When the audio signal may be expected to carry DC content, use of the DC cancelling filter of TDA1307 is recommended, to ensure correct and accurate peak detection.
handbook, full pagewidth
audio input from first half-band stage
+ -
+
audio output to peak detection block
DCEN = 1 zero DCEN = 0
LPF fo = 2 Hz
DCSH = 0 T DCSH = 1
MGB994
Fig.12 Schematic diagram of the DC filter.
1996 Jan 08
18
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, full pagewidth
audio input from peak detection block controlled multiplication factor
audio output to second half-band stage
18 FN 10
(desired level) from microprocessor register file FSS (fade speed) FCON 10
VOLUME CONTROL ALGORITHM
MGB985
Fig.13 Schematic diagram of the volume control block.
Fade function and volume control One of the main features of TDA1307 is a patented, advanced digital volume control with inherent fading function, exhibiting an accuracy and smoothness unsurpassed in presently available digital filters. Only the desired volume and the fade speed need to be instructed to the TDA1307, which can be realized in a single instruction via the microprocessor interface. The volume control function then autonomously performs automatic fade in or fade out to the desired volume by a natural, exponential approach. It allows for volume control to an accuracy of 0.1 dB over the range from 0 dB of full scale to beyond -100 dB. The speed of approach can be set over a wide range, varying from less than one second to over 23 seconds for a complete fade. Furthermore the fade algorithm manages the additional fading resolution, in excess of the 0.1 dB available for the volume desired level, needed to ensure gradual changes in volume at all times. Figure 13 illustrates the volume control block. Three data entities in the microprocessor register file pertain to the volume control block: a 10-bit control value for the desired volume (bits FN9 to FN0), a 10-bit control value for the fade speed (bits FSS9 to FSS0), and the fade function override bit, FCON. The volume control word ranges from 0 (representing a desired volume level or 0 dB) to 1023 (representing maximum desired volume level of zero or - dB). For values 1 to 1023, an LSB change of the volume control word represents 0.1 dB change of volume level. In changing from one volume level to the next desired volume level, the volume control block 1996 Jan 08 19
calculates and applies intermediate volume levels according to an exponential approach curve. The speed at which the approach curve progresses is determined by the value of the fade speed control word, FSS. FSS + 2 is the amount of time delay applied, in units of audio sample instants, before a next value on the exponential curve is calculated and applied. The total duration of an exponential fade operation is the product of the desired amount of volume change FN (in LSBs of the 10-bit control word) and the amount of delay per fade step FSS (in LSB times seconds), expressed as follows: ( FSS + 2 ) t fade, exp, total = FN x ---------------------------- , fs where fs is the base-band sampling frequency. Thus the longest fade time achievable, occurring in the event of maximum desired volume change FN = 1023, slowest speed setting FSS = 1023, and in the event that fs = 44.1 kHz, is 23.7 seconds. To smooth out fast volume changes however, the TDA1307 fade function adds extra resolution to the volume control by gradually changing from one exponential step to the next, by a linear transition. Whereas the 10-bit FN-value could not accomplish discrete attenuation steps finer than 0.1 dB, the linear transitional approach enhances volume change resolution to 15-bit. The volume level therefore never changes faster than one LSB of the 15-bit attenuation factor per audio sample. As soon as the linear transition reaches the value
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
determined by the exponential approach, the attenuation value remains stable until the next exponential value is due, which will again initially be approached linearly. For exponential fade speeds higher than the linear approach can follow, the approach remains linear unless the exponential approach curve is intersected. For fast volume decrease, the start of the approach will be linear, whereas for a fast volume increase, the course of the fade approach will be exponential at first, then saturating to linear. The fastest fade speed, for large volume changes, is therefore determined by the linear approach. For a maximum volume change at maximum speed, follows a fade time of (215 - 1)/44100 = 0.74 seconds. For immediate return to the maximum volume level without altering the volume and fade speed settings, bit FCON in the register file can be used. With this bit set to 1, the fade function is active and operates as described above. Resetting FCON to 0 will immediately deactivate the fade function, that is, return the volume level to maximum at the start of the next audio sample. Changing state of FCON from 0 to 1 will cause a fade according to the current settings of volume and speed control words FN and FSS. In Fig.14, a few fading examples illustrate the operation of the TDA1307 advanced digital volume control. Dither and scaling Prior to input to the noise shaper, final preprocessing is performed upon the eight times oversampled and interpolated audio data stream in the form of scaling and dither addition. The fixed scaling factor, a frequency-independent attenuation of 3 dB, is applied to the signal in order to provide the noise shaper with sufficient headroom. The application of dither is optional, selectable by means of bit DIT in the microprocessor register file. With DIT set to 1, fixed dither levels of value 2-6 + 2-5 and 2-6 - 2-5 are added alternately to the audio signal, at an alternation rate of 4fs. This amounts to a combination of an AC dither signal of frequency 4fs and amplitude -24 dB of full-scale, with a DC dither (offset) of 3.125% of full-scale peak amplitude. With DIT set to 0, no dithering, AC or DC, is performed. Although the addition of dither is made selectable in the TDA1307, it is generally recommended for use always, as dither is essential to the accurate conversion of low-level signals and reproduction of silence conditions by noise-shaping circuits. Third and fourth order noise shaping
TDA1307
The noise shaper constitutes the final audio processing stage of TDA1307, which takes the eight times oversampled and interpolated audio data stream from the digital filter as input, and by extreme oversampling and 1-bit end quantization processes the signal so that it can be converted to analog by a one-bit digital-to-analog converter. The order of the noise shaper is selectable, between 3rd and 4th order, by means of the register file bit NS (NS = 0: 3rd order, NS = 1: 4th order). Together with the final oversampling ratio, the noise shaper order determines the dynamic range (or accuracy) that the noise shaper can achieve (the oversampling ratio will depend on the system clock frequency and application mode used). Table 6 gives the dynamic range of the noise shaper as a function of these two parameters. Figures 15 and 16 show noise spectral density simulations of the third and fourth order noise shaper respectively, with a stimulus frequency of 1 kHz at a level of -10 dBfs, for 192 x 44.1 kHz oversampling. From the slope of the shaped noise spectrum outside the audio band, the order of noise shaping is apparent. It is important to note that, in contrast to normal fourth-order noise shaping, where an audio post-filter of equal order would be needed to compensate the slope of the quantization noise, the fourth-order noise shaper of the TDA1307 actually only needs third order post-filtering to obtain the same amount of stop-band suppression as with third order. The noise density of the fourth order noise shaper starts at a lower level for low frequencies, and only slightly exceeds the third-order curve in the 200 to 300 kHz region.
1996 Jan 08
20
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, full pagewidth
max
volume level
(FSS + 2)/fs 0.1 dB
1/fs
0 A B C D E F G time
MGB991
A: Fade out to zero (FN = 0). B: Fade in to maximum volume (FN = 1023). C: Fast volume decrease resulting in initial linear regulation. D: Slow volume decrease predominantly exponential. E: Volume regulation overridden by resetting FCON to 0. F: FN = 0, FSS = 0, FCON to 1 causes fastest maximum fade with linear regulation. G: Medium speed volume increase starts exponential, ends linear.
Fig.14 Volume control examples.
Table 6
Noise shaper dynamic range OVERSAMPLING/ORDER 128fs 192fs 3rd ORDER 105 dB 117 dB 4th ORDER 118 dB 134 dB
1996 Jan 08
21
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, full pagewidth
0
MGB992
Ao (dBfs) -50
-100
-150
-200 10
102
103
104
105 log frequency (Hz)
106
Fig.15 Noise shaper output spectrum (N = 3; 192fs).
handbook, full pagewidth
0
MGB993
Ao (dBfs) -50
-100
-150
-200 10
102
103
104
105 log frequency (Hz)
106
Fig.16 Noise shaper output spectrum (N = 4; 192fs). 1996 Jan 08 22
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VDD VI IIK IOK IO IDD, ISS PO, cell Tstg Tamb Ves Note 1. Input voltage should not exceed 6.5 V. THERMAL CHARACTERISTICS SYMBOL Rth j-a PARAMETER thermal resistance from junction to ambient in free air VALUE 39 PARAMETER supply voltages (pins 8, 21, 24, 29, 32 and 41) maximum input voltage DC clamp input diode current DC output clamp diode current; (output type 4 mA) DC output source or sink current; (output type 4 mA) DC VDD or GND current per supply pin power dissipation per output (type 4 mA) storage temperature operating ambient temperature electrostatic handling 100 pF; 1.5 k note 1 VI < -0.5 V or VI > VDD + 0.5 V VO < -0.5 V or VO > VDD + 0.5 V -0.5 V < VO < VDD + 0.5 V CONDITIONS MIN. -0.5 -0.5 - - - - - -55 -20 -2000
TDA1307
MAX. +6.5 VDD + 0.5 10 20 20 50 50 +150 +70 +2000 V V
UNIT
mA mA mA mA mA C C V
UNIT K/W
1996 Jan 08
23
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
CHARACTERISTICS VDD = 4.5 to 5.5 V; VSS = 0 V; Tamb = -20 to +70 C and oscillator frequency 33.8688 MHz; unless otherwise specified. SYMBOL Supplies VDDC1,2,3 VDDOSC VDDAR VDDAL Vdiff IDDC1,2,3 IDDOSC IDDAR IDDAL Inputs CLC1, CLC2, EFAB, SCK, WS, SD, SBCL, DA, SBDA, CDCC, TEST1 AND TEST2 VIL VIH ILI RI CI VIL VIH RI CI Outputs CDEC AND CMIC (TYPE 4 MA) VOL VOH CL VOL VOH CL LOW level output voltage HIGH level output voltage load capacitance IOL = 4 mA IOH = -4 mA - VDD-0.5 - IOL = 8 mA IOH = -8 mA - VDD-0.5 - - - - - - - 0.5 - 30 V V pF LOW level input voltage HIGH level input voltage input leakage current input resistance input capacitance note 1 note 1 note 2 note 3 - 0.7VDD -1 17 - note 1 note 1 note 3 - 0.8VDD 17 - - - - - - - - - - 0.3VDD - +1 134 10 V V A k pF supply voltage (pins 8, 21 and 41) supply voltage (pin 24) supply voltage (pin 32) supply voltage (pin 29) maximum difference between supplies supply current (pins 8, 21 and 41) supply current (pin 24) supply current (pin 32) supply current (pin 29) VDD = 5 V VDD = 5 V VDD = 5 V VDD = 5 V 4.5 4.5 4.5 4.5 - - - - - 5.0 5.0 5.0 5.0 - 75 2 2 1 5.5 5.5 5.5 5.5 tbf - - - - V V V V V mA mA mA mA PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
CL, RAB, POR, DSTB AND MODE LOW level input voltage HIGH level input voltage input resistance input capacitance 0.2VDD - 134 10 V V k pF
CDAC (TYPE TBF MA) LOW level output voltage HIGH level output voltage load capacitance 0.5 - 100 V V pF
1996 Jan 08
24
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
SYMBOL
PARAMETER
CONDITIONS -
MIN. - - - - - - - - - - - - -
TYP.
MAX.
UNIT
DOR, DOL, NDOR AND NDOL (TYPE CUSTOM MA) VOL VOH CL VOL VOH CL VOL VOH CL VOL VOH CL RLint LOW level output voltage HIGH level output voltage load capacitance IOL = 2 mA IOH = -2 mA 0.5 - 100 V V pF VDD-0.5 - IOL = 12 mA IOH = -12 mA - VDD-0.5 - IOL = 2 mA IOH = -2 mA - VDD-0.5 - IOL = 2 mA IOH = -2 mA - VDD-0.5 - 17
DOBM (TYPE 12 MA) LOW level output voltage HIGH level output voltage load capacitance 0.5 - 50 V V pF
DSR, DSL AND RESYNC (TYPE 2 MA) LOW level output voltage HIGH level output voltage load capacitance 0.5 - 50 V V pF
DA (TYPE 2 MA) LOW level output voltage HIGH level output voltage load capacitance internal load resistance 0.5 - 50 134 V V pF k
Crystal oscillator INPUT: XTAL1 gm Gv ILI CI Timing fXTAL fCL fSCK fWS tLB tHB tr tf tSU:DAT tHD:DAT tSU:WS tHD:WS operating frequency 33.8688 - - - 110 110 - - 20 0 20 0 - - fXTAL/768 - - - - - - - - MHz mutual conductance small-signal voltage gain input leakage current input capacitance f = 2 MHz Gv = gm x RO note 2 - - -1 - 0.4 72 - 10 - - +1 - A pF mS
SCK, WS, DATA, SBDA, SBCL AND EFAB (SEE FIGS 8 AND 9) SBCL clock frequency SCK clock frequency WS clock frequency clock time LOW clock time HIGH input rise time input fall time data set-up time data hold time WS set-up time WS hold time note 3 64fs 64fs - - - 20 20 - - - - Hz Hz Hz ns ns ns ns ns ns ns ns
1996 Jan 08
25
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
SYMBOL
PARAMETER
CONDITIONS -
MIN. - - - -
TYP.
MAX.
UNIT
MICROCONTROLLER INTERFACE (SEE FIGS 6 AND 7) fCK tCKL tCKH tDSM CL input clock frequency input clock time LOW input clock time HIGH microprocessor data set-up time after CL LOW-to-HIGH transition microprocessor data hold time after CL LOW-to-HIGH transition peak data set-up time after CL LOW-to-HIGH transition peak data hold time after CL LOW-to-HIGH transition delay to write after read delay to read after write 46fs - - - kHz s s s 2.0 2.0 1.0
tDHM tDSP tDHP tdRW tdWR DOBM CIRCUIT fDOBM tr tf tSU;DAT tHD;DAT fXTAL1 fCDEC fCMIC Notes
2.0 2.0 2.0 2.0 2.0 - CL = 50 pF CL = 50 pF - - 40 5 - - -
- - - - - 128fs - - - - 256fs 256fs 96fs
- - - - - - 10 10 - - - - -
s s s s s Hz ns ns ns ns
data output frequency output rise time output fall time data set-up time data hold time
CLOCK GENERATOR CIRCUIT (NOTE 4) XTAL1 input clock frequency CDEC output clock frequency CMIC output clock frequency slave mode Hz Hz Hz
1. Minimum VIL, maximum VIH are peak values to allow for transients. 2. II(min) measured at VI = 0 V; II(max) measured at VI = VDD; not valid for pins with pull-up/pull-down resistors. 3. II(min) measured at VI = 0 V (pull-up); II(max) measured at VI = VDD (pull-down); valid for pins with pull-up/pull-down resistors. 4. Crystal frequency: 33.8688 MHz (768fs), the oscillator circuit oscillates at a frequency that is approximately 0.01% above the crystal frequency. QUALITY SPECIFICATION In accordance with "SNW-FQ-611E". The numbers of the quality specification can be found in the "Quality Reference Handbook". This handbook can be ordered using the code 9397 750 00192.
1996 Jan 08
26
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
APPLICATION INFORMATION Application modes
TDA1307
TDA1307 can be used as a digital reconstruction filter for CD, DCC, DAB and DAT applications. The configuration for these different applications is given in Table 7. Table 7 Application modes CDCC 1 0 0 0 CRYSTAL 768fs - - - CLOCK INPUT - 256fs 256fs 256fs BITSTREAM OUTPUT 192fs 128fs 128fs 128fs SAMPLING FREQUENCY 44.1 kHz 32.0 or 44.1 or 48.0 kHz 32.0 kHz 32.0 or 44.1 or 48.0 kHz
MODE CD DCC DAB DAT
The crystal frequency for TDA1307, when operating in master mode, is 768fs (fs = 44.1 kHz). TDA1307 can also operate in slave mode, in which the clock input receives a clock signal of 256fs (fs = 32.0, 44.1 or 48.0 kHz). In the latter configuration, no resonator is connected to TDA1307. Basic application Figures 17 to 20 show the connections for an example of a complete bitstream reconstruction system, using TDA1307 together with TDA1547, as implemented in a demonstration application printed-circuit board. Figure 15 shows the connections pertaining to TDA1307. Both master and slave operation is possible, by setting of switches J1 and J2, and by programming the desired mode and frequency divisions by switch block SW1. Both test pins of TDA1307 are tied to ground in order to obtain immunity to crosstalk from the adjacent clock output CDAC. At pin POR (pin 20), an RC-timing network presets a typical power-on-reset LOW-time (10 ms for an instantaneously setting 5 V supply).
Typical application with TDA1547 Bitstream DAC The high-quality one-bit audio data stream produced by the TDA1307 is optimumly converted to analog using the TDA1547 high-performance bitstream digital-to-analog converter. The TDA1547 takes the data outputs DOL (pin 27) and DOR (pin 33) of the TDA1307 as input, clocked by TDA1307 output CDAC (pin 35), and converts the digital data to `one-bit' analog values (positive reference value and negative reference value) through a differentially configured high-speed, high-accuracy switched capacitor network. This differential application can be further enhanced to a double-differential application, combining the assertive data outputs with the complementary data outputs NDOL (pin 28) and NDOR (pin 34) into a set of two TDA1547s, by which it is possible to achieve additional noise margin. The application of Figs 17 to 19 is an example of a differential application. A schematic diagram of the double differential mode application is illustrated in Fig.20.
1996 Jan 08
27
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, full pagewidth
+5 V DC 100 F 0V DGND C C C
VSSC1 VDDC1 VSSC2 VDDC2 VSSC3 VDDC3 +5 V CON1 2 4 6 8 10 1 3 5 7 9 BIT CLOCK WORD CLOCK SERIAL DATA ERROR FLAG SCK WS SD EFAB 2 1 3 4 22 19 VDDOSC VSSOSC CDEC 47 CMIC 47 CMIC_out C CDEC_out CON3 XTAL1
(1)
47 k
40 POR 1 F 20
21
9
41
16
8
XSYS_IN 100 pF s J1 m 33.8688 MHz X1
CON2
23
XTAL2
(1)
100 k m J2 s 10 nF
3.3 H 10 pF 10 k 1 nF +5 V
10 k
RESYNC +5 V 4xR
10 pF
SW1 8 7 3 4 1 2 6 5
CDCC CLC2 CLC1 DSTB
24 18 17 14 13 7 25
SBCL (from decoder) SBDA
TDA1307
5 6 10 36 37 26 11 DSL 12 DSR 32 31 34 33 NDOR DOR CDAC DOL NDOL 15
CON4
DOBM 560 620
TR1 DIG_out CON5
TEST1 TEST2 MODE
+5 V
4.7 100 F
VDDAR CV SSAR
(to analog output stage TDA1547 circuit; optional)
VDDAL C VSSAL
35 29 30 42 RAB 39 CL 38 DA
MGB990
(to TDA1547 circuit)
27 28
(to/from microprocessor)
C = 100 nF chip capacitor. R = 10 k chip resistor. (1) s = slave mode switch position. m = master mode switch position.
Fig.17 Basic connections TDA1307.
1996 Jan 08
28
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, full pagewidth
NDOR
34 33 35 27 28
TDA1307
DOR CDAC DOL NDOL
DGND
IN R 3 1
CLK R 5
CLK L IN L 28 30 32
VSUB C
10
-5 V (digital) -5 V (digital)
+5 V (digital)
10 C
VDDD n.c.
2 4 6
31 29 27
VSSD n.c. VDDD L C C
10
+5 V (digital)
10 C 1.5 k 3.3 k
VDDD R
10
+5 V (digital) -5 V (digital)
-5 V (digital)
VSSD R C
7
26
VSSD L C
1.5 k 3.3 k
-5 V (analog)
560 3.3 k 220 F
Vref R C
TDA1547
8 25
Vref L C 220 F
560 3.3 k
-5 V (analog)
AGND DAC R - DAC R + DAC R
9 10 11 12 13 14 15 16
24 23 22 21 20 19 18 17
AGND DAC L - DAC L + DAC L AGND L n.c. + OUT L - OUT L VDDA
to analog output stage
AGND R n.c. + OUT R - OUT R
to analog output stage
-5 V (analog)
4.7 C
VSSA
4.7 C
+5 V (analog)
+5 V DC (digital) 0V -5 V DC (digital)
100 F 100 F
+5 V DC (analog) DGND 0V -5 V DC (analog)
100 F 100 F
AGND
MGB988
C = 100 nF chip capacitor.
Fig.18 Connections for TDA1307.
1996 Jan 08
29
k, full pagewidth
1996 Jan 08
220 pF 820 pF 13 k 23 22 21
Philips Semiconductors
High-performance bitstream digital filter
220 pF
56 pF 10 k 10 k
13 k
2.2 nF 1 k 1/2 IC3 3.3 k 470 33 nF 3.3 nF 1.62 k
100 H 2.61 k 1/2 IC3 560 pF
100 F
4.7
CON6
AUDIO OUTPUT LEFT
3.3 k
1.5 k
J5
DSL (optional from TDA1307) +15 V DC
KILL (optional)
19
18 DE-EMPHASIS (optional) J3 4.7 C IC3 DE-EMPHASIS (optional from decoder) 4.7 56 pF C 33 F 4.7 33 F IC4 C 33 F 4.7 C 33 F
ANALOG OUTPUT SECTION TDA1547
30
10 11 12 14 15 10 k 820 pF 13 k 3.3 k 220 pF 13 k 220 pF
-15 V DC 100 H 2.61 k 1/2 IC4 1.5 k
10 k 2.2 nF 1 k 1/2 IC4 3.3 k 470 33 nF 3.3 nF 1.62 k
100 F
4.7
CON7
AUDIO OUTPUT RIGHT
560 pF
J6
DSR (optional from TDA1307)
KILL (optional)
MGB987
DE-EMPHASIS (optional)
J4
Preliminary specification
TDA1307
C = 100 nF chip capacitor. IC3 = IC4 = NE5532(A) or equivalent.
Fig.19 Connections for output section of TDA1307.
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
TDA1307
handbook, full pagewidth
R
R1 -R1
+ -
= 2R1 + + =
2R2
TDA1547
DOR 20-bit, fs NDOR Rn -R2
=
4R
- R2 +
L2
audio output right
TDA1307
CDAC NDOL DOL Ln
-L2
+ -
=
2L2
TDA1547
-L1 L
+ + =
2L1
=
4L
- L2 +
audio output left
MGB986
Fig.20 Schematic diagram for double differential application.
1996 Jan 08
31
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
PACKAGE OUTLINE SDIP42: plastic shrink dual in-line package; 42 leads (600 mil)
TDA1307
SOT270-1
seating plane
D
ME
A2
A
L
A1 c Z e b1 wM (e 1) MH b 42 22
pin 1 index E
1
21
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 5.08 A1 min. 0.51 A2 max. 4.0 b 1.3 0.8 b1 0.53 0.40 c 0.32 0.23 D (1) 38.9 38.4 E (1) 14.0 13.7 e 1.778 e1 15.24 L 3.2 2.9 ME 15.80 15.24 MH 17.15 15.90 w 0.18 Z (1) max. 1.73
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT270-1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 90-02-13 95-02-04
1996 Jan 08
32
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities. In these situations reflow soldering is often used. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our "IC Package Databook" (order code 9398 652 90011). Soldering by dipping or by wave The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joint for more than 5 seconds. The total contact time of successive solder waves must not exceed 5 seconds. DEFINITIONS Data sheet status Objective specification Preliminary specification Product specification Short-form specification Limiting values
TDA1307
The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg max). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Repairing soldered joints Apply a low voltage soldering iron (less than 24 V) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds.
This data sheet contains target or goal specifications for product development. This data sheet contains preliminary data; supplementary data may be published later. This data sheet contains final product specifications. The data in this specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook.
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.
1996 Jan 08
33
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
NOTES
TDA1307
1996 Jan 08
34
Philips Semiconductors
Preliminary specification
High-performance bitstream digital filter
NOTES
TDA1307
1996 Jan 08
35
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113, Tel. +61 2 9805 4455, Fax. +61 2 9805 4466 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010, Fax. +43 160 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 689 211, Fax. +359 2 689 102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S, Tel. +45 32 88 2636, Fax. +45 31 57 0044 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615800, Fax. +358 9 61580920 France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex, Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 23 53 60, Fax. +49 40 23 536 300 Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS, Tel. +30 1 4894 339/239, Fax. +30 1 4814 240 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: see Singapore Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3, 20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108, Tel. +81 3 3740 5130, Fax. +81 3 3740 5077 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA, Tel. +48 22 612 2831, Fax. +48 22 612 2327 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000, Tel. +27 11 470 5911, Fax. +27 11 470 5494 South America: Rua do Rocio 220, 5th floor, Suite 51, 04552-903 Sao Paulo, SAO PAULO - SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 829 1849 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 3 301 6312, Fax. +34 3 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 632 2000, Fax. +46 8 632 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2686, Fax. +41 1 481 7730 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Talatpasa Cad. No. 5, 80640 GULTEPE/ISTANBUL, Tel. +90 212 279 2770, Fax. +90 212 282 6707 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 1997
Internet: http://www.semiconductors.philips.com
SCA55
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
513061/25/02/pp36
Date of release: 1996 Jan 08
Document order number:
9397 750 02844

▲Up To Search▲

Price & Availability of TDA1307

	To Download TDA1307 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .